Koyo Bearing Opinions? | Maverick/Comet Forums
WEBOct 18, 2004 · Koyo Bearings will manufacture needle roller bearings under the Koyo Torrington Needle Roller Bearings brand, which features an extensive range of radial and thrust needle roller bearings, as well as bearing assemblies and loose needles for automotive and industrial applications.
76 Mav 8" axle bearing install help. | Page 2 - Maverick
WEBApr 9, 2002 · 2) New ESPO 4-leaf springs and all hardware. 3) Made a steel spacer for the traction bar plate to get rid of the slop between the hole and the leaf spring bolt and welded in. 4) New traction bar bumpers (old ones were all mangled). 5) made 2 new spring perches, 1/4" thick steel and welded them on.
Can bad lifter(s) cause low oil pressure? | Page 3 - Maverick
WEBMay 27, 2011 · Bore wear and cam bearings aren't a good indicator of mileage on the bottomend in late model motors. I've seen many late model 5.0's with excellant bores (crosshatching still visible at over 100K miles) that could have used new rods and mains.(but not nearly as bad as those you pictured) This is due to Ford switching to low …
72 Mercury Comet GT in Germany | Page 51 - Maverick
WEBMay 9, 2009 · 1. Location: cologne, germany. Vehicle: 72 comet gt, 67 club wagon, 65 mustang. Good to see so many familiar faces replying to this thread. Jeff, the vibration has gotten a lot better since addressing the issues mentioned above. I think it was a combination of many issues, the wheel balance surely being one of the bigger things.
Rearend code | Maverick/Comet Forums
WEBMar 12, 2002 · Vehicle: 1975 maverick 4 door; 1971 Bronco frame off restoring. Does anybody have the codes for the rear end. I replaced the axle bearings on one axle and the other axle is gone. Bearings messed up the axle. This is for the 72 mav I going to look at the rear ends I have but, I need the code for the year that is on the plate. A 72 or 73 will work.
Inline six swaps | Maverick/Comet Forums
WEBAug 1, 2015 · Vehicle: 71 maverick. Knowing I'm in the right sub forum, I've been toting around the idea of installing an inline six from another donor. There are two jap engines that is look at, the 2jz, and the 7m, which are both Toyota inline sixes. I didnt mention Nissan RB engines, cause I'm trying to choose an engine that is readily available.
8" Posi center swap | Maverick/Comet Forums
WEBNov 6, 2014 · Vehicle: ---- 1976 Comet --- 1974 Maverick- - '61 Comet T'Bolt Six ---- 'quite a few projects ... I have an - 8" center differential that a PO put a SPOOL in, it has 3.80 :1 Ford gears. I'm swapping in a Posi center carrier unit . Pinion is not being removed - Only carrier is swapping not gear set, ring gear is re-installed on new carrier.
Roller spring perches . . . | Maverick/Comet Forums
WEBApr 21, 2006 · If I have it right, I need 4 of the Timken bearings, 2 bushings, and 2 60-63 falcon spring perches. The rest is easy to put together I'm assuming. Where is a good place to look for the older falcon spring perches, I didn't see old falcons at the junk yard Bryant and I went to. Why not just buy these from ebay for $30 instead of the ones for $200?
8 inch rear swap question.. | Maverick/Comet Forums
WEBMay 12, 2007 · Location: Nevada. Vehicle: 1971 Maverick Grabber Clone, 1971 Maverick project. I believe it was the first year for production that had the smaller rear end. My '71 had 8". I swapped in one from a '74 with zero problems and used the original drive shaft. Micah. 71Mavrk, Jan 4, 2015.
Maverick Rear End Width | Maverick/Comet Forums
WEBJan 22, 2008 · 1. Location: GA. Vehicle: '74 Maverick 302 5-Speed.'60 Falcon V8. '63.5 Falcon HT. I notice that the rear end charts on the internet say that a Maverick rear end is 56.5" wide. I measured and came up with closer to 55.75".